Make Your Own Wedding Invitations
Wedding Greeting Cards
- On your Golden Wedding Anniversary 50 wonderful yearsSKU: WB33-C£3.60
bolsasdeplastico.pe,/Ebionize1109891.html,of,85,Spark,Pack,Plug,,1,$2,Autolite,Resistor,Automotive , Replacement Parts,Copper $2 Autolite 85 Copper Resistor Spark Plug, Pack of 1 Automotive Replacement Parts bolsasdeplastico.pe,/Ebionize1109891.html,of,85,Spark,Pack,Plug,,1,$2,Autolite,Resistor,Automotive , Replacement Parts,Copper Autolite 85 Copper Cheap super special price Resistor Spark of 1 Plug Pack $2 Autolite 85 Copper Resistor Spark Plug, Pack of 1 Automotive Replacement Parts Autolite 85 Copper Cheap super special price Resistor Spark of 1 Plug Pack
Autolite Copper Core spark plugs deliver quick starts, good fuel economy, and smooth acceleration. The copper-glass seal bonds insulator and terminal post center electrode together to ensure full required voltage at spark gap, creating a gas-tight seal that is 100 percent leak-proof. Copper Core spark plugs feature a cold-formed steel shell and precision rolled threads, and a one-piece terminal post that adds strength. The multi-rib insulator reduces the danger of "flash-over" to prevent misfires, and the resistor reduces radio frequency interference (RFI) and electrode erosion. The full copper core electrode provides better performance in all conditions. Autolite Copper Core plugs are your industry standard.
Guaranteed to deliver quick starts, good fuel economy and smooth acceleration. Autolite Copper Core plugs are your industry standard.
Provides a center wire platinum firing tip. Benefits include: reduced gap erosion, fewer misfires, better performance and more durability. Guaranteed for four years.
Features platinum-to-platinum firing. Virtually eliminates gap erosion, reduces misfires, and provides improved durability. It's the superior-performing spark plug providing preferred technology for DIS engines. Guaranteed for five years.
These spark plugs are one of the brand's most technologically advanced spark plugs ever. With an iridium-enhanced 0.6 mm finewire design and proprietary platinum sidewire technology, these spark plugs provide better durability and a more focused ignition for better overall ignitability and optimum performance. Guaranteed for seven years.
Autolite highly recommends that you consult with your vehicle’s owner’s manual for any specific instructions for changing the spark plugs. Engines can vary widely by make and model. These instructions should be considered for general guidance only.
Replacing spark plugs can be a simple job, if you take things one step at a time. Given a basic understanding of mechanical matters, here's a guide to the proper procedures in changing spark plugs.
1. Carefully remove the spark plug wires. Grasp the plug wire boot, twist about one-quarter turn to break the seal, then lift straight off. Use plug boot pullers if the boot doesn't break free easily. Number plug wires with tape as you remove them to avoid crossing them. (illus. 1)
2. Loosen each spark plug so it can be removed. Clean the seat area with a blast of compressed air, or by blowing through a soda straw. This prevents dirt from falling into the combustion chamber when the old plugs are removed. (illus. 2)
3. Remove the plugs and line them up in cylinder order. Inspection of the firing ends of the plugs can identify a number of engine problems that may need correction. (illus. 3)
4. Gap new plugs as recommended in your owner's manual or a Spark Plug Catalog. Use a feeler gauge to measure the gap between the center and ground electrode. The gauge should pass through snugly but easily. If it's too loose or too tight, reset the gap.
5. Screw new plugs in by hand until tight. If the plug starts to go in hard, use a thread chaser to clean the threads. Use a torque wrench to tighten the spark plugs following the manufacturer's recommendations, or refer to a torque chart in the Spark Plug Catalog. If you don't have a torque wrench, see the bottom of the torque chart for hand tightening recommendations.
6. Replace spark plug wires in the correct order. Check to see if the boots are brittle or cracked, and if there is corrosion on the connector inside the boot. If any of these conditions are present, the spark plug wire should be replaced.
7. Start the engine. If it misfires or idles roughly, the wires are crossed or not connected to the plugs correctly. Check the firing order and connections closely.
Award Winning Company
Super Fast Shipping
No Minimum Order
5 Star Customer Service
100% Secure Shopping